config BR2_TARGET_UBOOT bool "U-Boot" help Build "Das U-Boot" Boot Monitor if BR2_TARGET_UBOOT choice prompt "Build system" default BR2_TARGET_UBOOT_BUILD_SYSTEM_LEGACY config BR2_TARGET_UBOOT_BUILD_SYSTEM_LEGACY bool "Legacy" help Select this option if you use an old U-Boot (older than 2015.04), so that we use the old build system. config BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG bool "Kconfig" help Select this option if you use a recent U-Boot version (2015.04 or newer), so that we use the Kconfig build system. endchoice if BR2_TARGET_UBOOT_BUILD_SYSTEM_LEGACY config BR2_TARGET_UBOOT_BOARDNAME string "U-Boot board name" help One of U-Boot supported boards to be built. This will be suffixed with _config to meet U-Boot standard naming. See boards.cfg in U-Boot source code for the list of available configurations. endif choice prompt "U-Boot Version" help Select the specific U-Boot version you want to use config BR2_TARGET_UBOOT_LATEST_VERSION bool "2016.05" config BR2_TARGET_UBOOT_CUSTOM_VERSION bool "Custom version" help This option allows to use a specific official versions config BR2_TARGET_UBOOT_CUSTOM_TARBALL bool "Custom tarball" config BR2_TARGET_UBOOT_CUSTOM_GIT bool "Custom Git repository" config BR2_TARGET_UBOOT_CUSTOM_HG bool "Custom Mercurial repository" config BR2_TARGET_UBOOT_CUSTOM_SVN bool "Custom Subversion repository" endchoice config BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE string "U-Boot version" depends on BR2_TARGET_UBOOT_CUSTOM_VERSION config BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION string "URL of custom U-Boot tarball" depends on BR2_TARGET_UBOOT_CUSTOM_TARBALL if BR2_TARGET_UBOOT_CUSTOM_GIT || BR2_TARGET_UBOOT_CUSTOM_HG || BR2_TARGET_UBOOT_CUSTOM_SVN config BR2_TARGET_UBOOT_CUSTOM_REPO_URL string "URL of custom repository" default BR2_TARGET_UBOOT_CUSTOM_GIT_REPO_URL \ if BR2_TARGET_UBOOT_CUSTOM_GIT_REPO_URL != "" # legacy config BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION string "Custom repository version" default BR2_TARGET_UBOOT_CUSTOM_GIT_VERSION \ if BR2_TARGET_UBOOT_CUSTOM_GIT_VERSION != "" # legacy help Revision to use in the typical format used by Git/Mercurial/Subversion E.G. a sha id, a tag, branch, .. endif config BR2_TARGET_UBOOT_VERSION string default "2016.05" if BR2_TARGET_UBOOT_LATEST_VERSION default BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE \ if BR2_TARGET_UBOOT_CUSTOM_VERSION default "custom" if BR2_TARGET_UBOOT_CUSTOM_TARBALL default BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION \ if BR2_TARGET_UBOOT_CUSTOM_GIT || BR2_TARGET_UBOOT_CUSTOM_HG || BR2_TARGET_UBOOT_CUSTOM_SVN config BR2_TARGET_UBOOT_PATCH string "Custom U-Boot patches" help A space-separated list of patches to apply to U-Boot. Each patch can be described as an URL, a local file path, or a directory. In the case of a directory, all files matching *.patch in the directory will be applied. Most users may leave this empty if BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG choice prompt "U-Boot configuration" default BR2_TARGET_UBOOT_USE_DEFCONFIG config BR2_TARGET_UBOOT_USE_DEFCONFIG bool "Using an in-tree board defconfig file" config BR2_TARGET_UBOOT_USE_CUSTOM_CONFIG bool "Using a custom board (def)config file" endchoice config BR2_TARGET_UBOOT_BOARD_DEFCONFIG string "Board defconfig" depends on BR2_TARGET_UBOOT_USE_DEFCONFIG help Name of the board for which U-Boot should be built, without the _defconfig suffix. config BR2_TARGET_UBOOT_CUSTOM_CONFIG_FILE string "Configuration file path" depends on BR2_TARGET_UBOOT_USE_CUSTOM_CONFIG help Path to the U-Boot configuration file. endif config BR2_TARGET_UBOOT_NEEDS_DTC bool "U-Boot needs dtc" select BR2_PACKAGE_HOST_DTC help Select this option if your U-Boot board configuration requires the Device Tree compiler to be available. choice prompt "U-Boot binary format" default BR2_TARGET_UBOOT_FORMAT_BIN config BR2_TARGET_UBOOT_FORMAT_AIS bool "u-boot.ais" help AIS (Application Image Script) is a format defined by TI. It is required to load code/data on OMAP-L1 processors. u-boot.ais contains U-Boot with the SPL support. config BR2_TARGET_UBOOT_FORMAT_BIN bool "u-boot.bin" config BR2_TARGET_UBOOT_FORMAT_DTB_IMG bool "u-boot-dtb.img" config BR2_TARGET_UBOOT_FORMAT_IMG bool "u-boot.img" config BR2_TARGET_UBOOT_FORMAT_IMX bool "u-boot.imx" config BR2_TARGET_UBOOT_FORMAT_NAND_BIN bool "u-boot-nand.bin" config BR2_TARGET_UBOOT_FORMAT_KWB depends on BR2_arm bool "u-boot.kwb (Marvell)" config BR2_TARGET_UBOOT_FORMAT_LDR depends on BR2_bfin bool "u-boot.ldr" config BR2_TARGET_UBOOT_FORMAT_ELF bool "u-boot.elf" config BR2_TARGET_UBOOT_FORMAT_SB depends on BR2_arm bool "u-boot.sb (Freescale i.MX28)" config BR2_TARGET_UBOOT_FORMAT_SD depends on BR2_arm bool "u-boot.sd (Freescale i.MX28)" help This is Freescale i.MX28 SB format, with a header for booting from an SD card. U-boot includes an mxsboot tool to generate this format, starting from 2011.12. See doc/README.mxs (or doc/README.mx28_common before 2013.07) config BR2_TARGET_UBOOT_FORMAT_NAND depends on BR2_arm bool "u-boot.nand (Freescale i.MX28)" help This is Freescale i.MX28 BootStream format (.sb), with a header for booting from a NAND flash. U-boot includes an mxsboot tool to generate this format, starting from 2011.12. There are two possibilities when preparing an image writable to NAND flash: 1) The NAND was not written at all yet or the BCB (Boot Control Blocks) is broken. In this case, the NAND image 'u-boot.nand' needs to written. 2) The NAND flash was already written with a good BCB. This applies after 'u-boot.nand' was correctly written. There is no need to write the BCB again. In this case, the bootloader can be upgraded by writing 'u-boot.sb'. To satisfy both cases, the 'u-boot.nand' image obtained from mxsboot as well as the U-Boot make target 'u-boot.sb' are copied to the binaries directory. See doc/README.mxs (or doc/README.mx28_common before 2013.07) if BR2_TARGET_UBOOT_FORMAT_NAND config BR2_TARGET_UBOOT_FORMAT_NAND_PAGE_SIZE int "NAND page size" default 2048 help The NAND page size of the targets NAND flash in bytes as a decimal integer value. The value provided here is passed to the -w option of mxsboot. config BR2_TARGET_UBOOT_FORMAT_NAND_OOB_SIZE int "NAND OOB size" default 64 help The NAND OOB size of the targets NAND flash in bytes as a decimal integer value. The value provided here is passed to the -o option of mxsboot. config BR2_TARGET_UBOOT_FORMAT_NAND_ERASE_SIZE int "NAND erase size" default 131072 help The NAND eraseblock size of the targets NAND flash in bytes as a decimal integer value. The value provided here is passed to the -e option of mxsboot. endif config BR2_TARGET_UBOOT_FORMAT_CUSTOM bool "Custom (specify below)" help On some platforms, the standard U-Boot binary is not called u-boot.bin, but u-boot.bin. If this is your case, you should select this option and specify the correct name in BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME. endchoice config BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME string "U-Boot binary format: custom name" depends on BR2_TARGET_UBOOT_FORMAT_CUSTOM help Specify the correct name of the output binary created by U-Boot, if it is not one of the default names. For example: u-boot_magic.bin config BR2_TARGET_UBOOT_OMAP_IFT depends on BR2_TARGET_UBOOT_FORMAT_BIN depends on BR2_arm || BR2_armeb select BR2_PACKAGE_HOST_OMAP_U_BOOT_UTILS bool "produce a .ift signed image (OMAP)" help Use gpsign to produce an image of u-boot.bin signed with a Configuration Header for booting on OMAP processors. This allows U-Boot to boot without the need for an intermediate bootloader (e.g. x-loader) if it is written on the first sector of the boot medium. This only works for some media, such as NAND. Check your chip documentation for details. You might also want to read the documentation of gpsign, the tool that generates the .ift image, at: https://github.com/nmenon/omap-u-boot-utils/blob/master/README if BR2_TARGET_UBOOT_OMAP_IFT config BR2_TARGET_UBOOT_OMAP_IFT_CONFIG string "gpsign Configuration Header config file" help The Configuration Header (CH) config file defines the desired content of the CH for the signed image. It usually contains external RAM settings and possibly other external devices initialization. The omap-u-boot-utils software contains example configuration files for some boards: https://github.com/nmenon/omap-u-boot-utils/tree/master/configs endif config BR2_TARGET_UBOOT_SPL bool "Install U-Boot SPL binary image" depends on !BR2_TARGET_XLOADER help Install the U-Boot SPL binary image to the images directory. SPL is a first stage bootloader loaded into internal memory in charge of enabling and configuring the external memory (DDR), and load the u-boot program into DDR. config BR2_TARGET_UBOOT_SPL_NAME string "U-Boot SPL binary image name" default "spl/u-boot-spl.bin" depends on BR2_TARGET_UBOOT_SPL help This is the name of the SPL binary, generated during u-boot build. For most platform it is spl/u-boot-spl.bin but not always. It is MLO on OMAP for example. config BR2_TARGET_UBOOT_ZYNQ_IMAGE bool "Generate image for Xilinx Zynq" depends on BR2_arm depends on BR2_TARGET_UBOOT_SPL depends on BR2_TARGET_UBOOT_FORMAT_DTB_IMG help Generate the BOOT.BIN file from U-Boot's SPL. The image boots the Xilinx Zynq chip without any FPGA bitstream. A bitstream can be loaded by the U-Boot. The SPL searchs for u-boot-dtb.img file so this U-Boot format is required to be set. config BR2_TARGET_UBOOT_ALTERA_SOCFPGA_IMAGE_CRC bool "CRC SPL image for Altera SoC FPGA" depends on BR2_arm depends on BR2_TARGET_UBOOT_SPL help Generate SPL image fixed by the mkpimage tool to enable booting on the Altera SoC FPGA based platforms. menuconfig BR2_TARGET_UBOOT_ENVIMAGE bool "Environment image" help Generate a valid binary environment image from a text file describing the key=value pairs of the environment. The environment image will be called uboot-env.bin. if BR2_TARGET_UBOOT_ENVIMAGE config BR2_TARGET_UBOOT_ENVIMAGE_SOURCE string "Source files for environment" help Text files describing the environment. Files should have lines of the form var=value, one per line. Blank lines and lines starting with a # are ignored. Multiple source files are concatenated in the order listed. config BR2_TARGET_UBOOT_ENVIMAGE_SIZE string "Size of environment" help Size of envronment, can be prefixed with 0x for hexadecimal values. config BR2_TARGET_UBOOT_ENVIMAGE_REDUNDANT bool "Environment has two copies" help Some platforms define in their U-Boot configuration that the U-Boot environment should be duplicated in two locations (for extra safety). Check your U-Boot configuration for the CONFIG_ENV_ADDR_REDUND and CONFIG_ENV_SIZE_REDUND settings to see if this is the case for your platform. If it is the case, then you should enable this option to ensure that the U-Boot environment image generated by Buildroot is compatible with the "redundant environment" mechanism of U-Boot. endif # BR2_TARGET_UBOOT_ENVIMAGE endif # BR2_TARGET_UBOOT